Golden Valley Paving Inc
Asphalt Services

What Is Asphalt Milling, and Why Do It?

Milling grinds off the worn top layer of asphalt so a new surface can go down at the right height. Here's how it works, when you need it, and what happens to the old asphalt.

Golden Valley Paving Team November 4, 2026 Asphalt Services
What Is Asphalt Milling, and Why Do It?

What Is Asphalt Milling, and Why Do It?

Last updated: November 2026

Short answer: Asphalt milling is the process of grinding off the top layer of an asphalt surface with a milling machine, usually 1 to 3 inches deep. It removes worn, cracked or uneven asphalt so a new layer can be paved at the right height, keeping the surface level with curbs, gutters, drains and doorways. The ground-up asphalt can be recycled into new pavement.

Milling is often the first step in resurfacing a parking lot or road. It's what lets you put down fresh asphalt without raising the surface higher every time.

Long stretch of smooth paved asphalt road under a bright sky

How Does Asphalt Milling Work?

A milling machine uses a large rotating drum covered in carbide teeth. As the machine moves forward, the drum chews into the pavement and grinds it into small pieces. A conveyor loads the material into a truck. The crew sets the depth so only the damaged layer comes off and the sound pavement below stays in place.

What's left is a rough, grooved surface. That texture actually helps. Once it's swept clean and tack coated, it gives the new asphalt a strong surface to bond to.

When Do You Need Asphalt Milling?

  • Before resurfacing. Milling removes the damaged top layer so the overlay sits on a clean, solid surface.
  • To keep heights right. Each overlay adds height. Without milling, a lot eventually rises above curbs and gutters, and water starts running toward buildings instead of drains.
  • To fix uneven surfaces. Ruts, bumps and shoving can be milled flat before paving.
  • Around edges and transitions. Edge milling along curbs, gutters and building entrances lets the new layer tie in smoothly, with no lip to trip on.
  • To restore drainage. Milling can correct the slope of an area that holds water.

Full-Width Milling vs. Edge Milling: What's the Difference?

Full-width milling removes the top layer across the whole surface. It's used when the top layer is worn everywhere or the surface has been built up too high.

Edge milling, sometimes called a wedge or butt-joint cut, removes asphalt only along curbs, gutters and other edges. The middle of the lot keeps its existing asphalt, and the new layer tapers in cleanly at the edges. It's a common way to resurface without full-width milling.

What Happens to the Milled Asphalt?

Asphalt is highly recyclable. Milled material, known as reclaimed asphalt pavement or RAP, is commonly mixed back into new hot-mix asphalt or used as a base material. The National Asphalt Pavement Association describes asphalt as America's most recycled product. Reusing it keeps material out of landfills and makes new pavement less resource-heavy.

Is Milling the Same as Removing the Whole Lot?

No. Milling takes off only the top layer. Full removal, or full-depth replacement, takes out all of the asphalt and often the base too. That's needed when the base has failed. If you're trying to decide which your property needs, read our guide on when to repair, resurface or replace asphalt. Our asphalt services cover milling, cutting, removal and new paving.

How Long Does Milling Take?

Milling moves fast. A typical commercial lot can often be milled in a day, and paving usually follows right behind so the surface isn't left rough for long. On busy properties, work can be done in sections so part of the lot stays open.

Frequently Asked Questions

How deep does asphalt milling go?

Most milling removes about 1 to 3 inches, depending on how deep the damage goes and how thick the new layer will be.

Can you drive on a milled surface?

Yes, for short periods. It's rough and loud, so new asphalt usually goes down soon after milling.

Does milling work on driveways?

It can, especially where a driveway meets a garage slab or sidewalk and a new layer would leave a lip. Most milling work is on parking lots and roads.

Do you do asphalt milling in Fresno and Clovis?

Yes. We provide asphalt milling across Fresno, Clovis and the Central Valley, usually as part of a resurfacing project.

Get Your Free Milling and Paving Estimate

Golden Valley Paving Inc is a family-owned, licensed and insured paving contractor with 20+ years of experience and 500+ projects completed across Fresno, Clovis and the Central Valley. See our paving services.

Get your free estimate and we'll respond within 1 business day. Or call (559) 765-7172. We're open 7 days a week.

Ready to start your paving project?

Get a free, no-obligation estimate from Golden Valley Paving Inc. — serving Fresno, Clovis, Visalia, Madera, and surrounding Central Valley communities.